2024 100% Free HPE7-A01 Daily Practice Exam With 121 Questions
HPE7-A01 exam torrent HP study guide
HP HPE7-A01 certification exam is an important credential that validates the skills and knowledge of IT professionals in designing and implementing enterprise-level wireless LAN solutions. HPE7-A01 exam is intended for individuals who have experience in configuring and troubleshooting Aruba products and solutions in complex environments. Aruba Certified Campus Access Professional Exam certification is ideal for network professionals, wireless engineers, and system administrators who want to enhance their skills in wireless networking and become Aruba Certified Campus Access Professionals.
NEW QUESTION # 13
Which method is used to onboard a new UXI in an existing environment with 802 1X authentication? (The sensor has no cellular connection)
- A. Connect the new UXI from an already installed one and adjust the initial configuration.
- B. Use the UXI app on your smartphone and connect the UXI via Bluetooth
- C. Use the CLI via the serial cable and adjust the initial configuration.
- D. Use the Aruba installer app on your smartphone to scan the barcode
Answer: B
Explanation:
Explanation
To onboard a new UXI in an existing environment with 802.1X authentication, you need to use the UXI app on your smartphone and connect the UXI via Bluetooth. The UXI app allows you to scan the QR code on the UXI sensor and configure its network settings, such as SSID, password, IP address, etc. The Bluetooth connection allows you to communicate with the UXI sensor without requiring any network access or cellular connection. The other options are incorrect because they either do not use the UXI app or do not use Bluetooth. References:
https://www.arubanetworks.com/products/network-management-operations/analytics-monitoring/user-experienc
https://help.centralon-prem.arubanetworks.com/2.5.4/documentation/online_help/content/nms-on-prem/aos-cx/g
NEW QUESTION # 14
You are troubleshooting an issue with a pair of Aruba CX 8360 switches configured with VSX Each switch has multiple VRFs. You need to find the IP address of a particular client device with a known MAC address You run the "show arp" command on the primary switch in the pair but do not find a matching entry for the client MAC address.
The client device is connected to an Aruba CX 6100 switch by VSX LAG.
Which action can be used to find the IP address successfully?
- A.
- B.
- C.
- D.
Answer: A
Explanation:
Explanation
The show arp command displays the ARP table for a specific VRF or all VRFs on the switch. The ARP table contains the IP address to MAC address mappings for hosts that are directly connected to the switch or reachable through a gateway. If the client device is connected to another switch by VSX LAG, the ARP entry for the client device will not be present on the primary switch unless it has communicated with it recently.
Therefore, to find the IP address of the client device, the administrator should run the show arp command on the secondary switch in the VSX pair, specifying the VRF name that contains the client device's subnet.
References:
https://techhub.hpe.com/eginfolib/Aruba/OS-CX_10.04/5200-6692/GUID-9B8F6E8F-9C7A-4F0D-AE7B-9D8E
NEW QUESTION # 15
Describe the difference between Class of Service (CoS) and Differentiated Services Code Point (DSCP).
- A. CoS is only used to determine CLASS of traffic DSCP is only used to differentiate between different Classes.
- B. CoS has much finer granularity than DSCP
- C. CoS is only contained in VLAN Tag fields DSCP is in the IP Header and preserved throughout the IP packet flow
- D. They are similar and can be used interchangeably.
Answer: C
Explanation:
Explanation
CoS and DSCP are both methods of marking packets for quality of service (QoS) purposes. QoS is a mechanism that allows network devices to prioritize and differentiate traffic based on certain criteria, such as application type, source, destination, etc. CoS stands for Class of Service and is a 3-bit field in the 802.1Q VLAN tag header. CoS can only be used on Ethernet frames that have a VLAN tag, and it can only be preserved within a single VLAN domain. DSCP stands for Differentiated Services Code Point and is a 6-bit field in the IP header. DSCP can be used on any IP packet, regardless of the underlying layer 2 technology, and it can be preserved throughout the IP packet flow, unless it is modified by intermediate devices.
References:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/qos/configuration/15-mt/qos-15-mt-book/qos-overview.html
https://www.cisco.com/c/en/us/support/docs/lan-switching/8021q/17056-741-4.html
https://www.cisco.com/c/en/us/support/docs/quality-of-service-qos/qos-packet-marking/10103-dscpvalues.html
NEW QUESTION # 16
Your customer is having issues with Wi-Fi 6 clients staying connected to poor-performing APs when a higher throughput APs are closer. Which technology should you implement?
- A. Clearpass
- B. ARM
- C. Airmatch
- D. ClientMatch
Answer: D
Explanation:
Explanation
Wi-Fi 6 is an industry certification for products that support the new wireless standard 802.11ax, also known as "high-efficiency wireless". Wi-Fi 6 offers increased capacities, improved resource utilization and higher throughput speeds than previous standards.
Option B: ClientMatch
This is because option B shows how to use ClientMatch to optimize the wireless performance of Wi-Fi 6 clients on a UniFi network. ClientMatch is a feature that uses machine learning to analyze the traffic patterns of each client and assign them to the best available AP based on their location, device type, and network conditions2.
Therefore, option B is the best technology to implement for your customer's issue.
1: https://help.ui.com/hc/en-us/articles/221029967-UniFi-Network-Optimizing-Wireless-Connectivity 2:
https://help.ui.com/hc/en-us/articles/360012947634-UniFi-Network-Optimizing-Wireless-Speeds
NEW QUESTION # 17
Refer to the exhibit.
A company has deployed 200 AP-635 access points. To but is not working as expected What would be the correct action to fix the issue?
- A. Change the SSID to WPA3-Enterpnse (CNSA).
- B. Change the SSID to WPA3-Enhanced Open
- C. Change the SSID to WPA3-Enterprise (CCM).
- D. Change the SSID to WPA3-Personal
Answer: A
Explanation:
Explanation
According to the Aruba Campus Access Professional documents1, WPA3-Enterprise is a security mode that supports 802.1X authentication and encryption with either AES-CCM or AES-GCMP. WPA3-Enterprise also optionally adds usage of Suite-B 192-bit minimum-level security suite that is aligned with Commercial National Security Algorithm (CNSA) for enterprise networks2. This mode provides the highest level of security and is suitable for government and financial institutions.
The exhibit shows that the SSID is configured with WPA3-Enterprise (CCM), which uses AES-CCM as the encryption protocol. However, this mode is not compatible with some devices that require CNSA compliance.
Therefore, changing the SSID to WPA3-Enterprise (CNSA) would fix the issue and allow all devices to connect to the network.
NEW QUESTION # 18
you need to have different routing-table requirements With Aruba CX 6300 VSF configuration.
Assuming the correct layer-2 VLAN already exists, how would you create a new SVI for a separate routing table?
- A. Create a new SVI and use attach command.
- B. Create a new routing table, and attach VLANS to it
- C. create a new VLAN, and attach the VRF to it.
- D. Create a new VLAN. and attach the routing table to it
Answer: A
Explanation:
The correct answer is C. Create a new SVI and use attach command.
To create a new SVI for a separate routing table, you need to use the attach command to associate the SVI with a VRF (Virtual Routing and Forwarding) instance. A VRF is a logical entity that allows multiple routing tables to coexist on the same switch. Each VRF has its own set of interfaces, routing protocols, and routes that are isolated from other VRFs.
According to the AOS-CX Virtual Switching Framework (VSF) Guide1, one of the steps to configure VRF-aware VSF is:
Configure the VRFs on each member switch and assign the SVIs to the respective VRFs using the attach command. For example:
switch(config)# vrf red
switch(config-vrf)# exit
switch(config)# interface vlan 10
switch(config-if-vlan)# ip address 10.1.1.1/24
switch(config-if-vlan)# attach vrf red
The above commands create a VRF named red and assign VLAN 10 SVI to it. The SVI has an IP address of 10.1.1.1/24.
The other options are incorrect because:
A) You cannot attach a VRF to a VLAN directly. You need to create an SVI for the VLAN and then attach the VRF to the SVI.
B) You cannot create a new routing table manually. You need to create a VRF and then use routing protocols or static routes to populate the routing table for the VRF.
D) You cannot attach a routing table to a VLAN directly. You need to create an SVI for the VLAN and then attach a VRF that has a routing table associated with it.
NEW QUESTION # 19
You must ensure the HPEAruba network you are configuring for a client is capable of plug-and-play provisioning of access points. What enables this capability?
- A. CSMA
- B. SRTP
- C. UCC Service
- D. LLDP-MED
Answer: C
Explanation:
Explanation
The capability that enables plug-and-play provisioning of access points in an HPE Aruba network is the UCC Service. The UCC Service is a cloud-based service that allows the access points to automatically discover and connect to the Aruba Central management platform without any manual intervention. The UCC Service also provides zero-touch configuration, firmware updates, and monitoring for the access points1.
The other options are incorrect because:
* B. LLDP-MED: LLDP-MED is a protocol that enhances the interoperability between network devices
* and IP phones. It does not enable plug-and-play provisioning of access points2.
* C. SRTP: SRTP is a protocol that provides encryption and authentication for voice and video traffic. It does not enable plug-and-play provisioning of access points3.
* D. CSMA: CSMA is a protocol that regulates how devices share a common medium, such as a wireless channel. It does not enable plug-and-play provisioning of access points.
NEW QUESTION # 20
Match the solution components of NetConductor (Options may be used more than once or not at all.)
Answer:
Explanation:
Explanation
Client Insights matches with Built in , AI powered client visibility and fingerprinting capability that leverages infrastructure telemetry and ML based classification models to eliminate network bling spots Client Insights is a solution component of NetConductor that provides built-in, AI-powered client visibility and fingerprinting capability that leverages infrastructure telemetry and ML-based classification models to eliminate network blind spots. Client Insights uses machine learning to automatically detect, identify, and classify devices on the network, such as IoT devices, BYOD devices, or rogue devices. Client Insights also provides behavioral analytics and anomaly detection to monitor device performance and security posture.
Client Insights helps network administrators gain visibility into the device landscape, enforce granular access policies, and troubleshoot issues faster. References:
https://www.arubanetworks.com/products/network-management-operations/central/netconductor/
https://www.arubanetworks.com/assets/wp/WP_NetConductor.pdf
Cloud Auth matches with Enables fictionless onboarding of end users and client devices either through MAC address-based authentication or through integrations with common cloud identity stores Cloud Auth is a solution component of NetConductor that enables frictionless onboarding of end users and client devices either through MAC address-based authentication or through integrations with common cloud identity stores. Cloud Auth is a cloud-native network access control (NAC) solution that is delivered via Aruba Central. Cloud Auth allows network administrators to define user and device groups, assign roles and policies, and enforce access control across wired and wireless networks. Cloud Auth supports MAC authentication for devices that do not support 802.1X, as well as integrations with cloud identity providers such as Azure AD, Google Workspace, Okta, etc. References:
https://www.arubanetworks.com/products/network-management-operations/central/netconductor/
https://www.arubanetworks.com/assets/wp/WP_NetConductor.pdf
The Fabric Wizard matches with Simplifies the creation of the overlays using an intuitive graphical user interface and automatic generation of configuration instructions that are pushed to switches and gateways The Fabric Wizard is a solution component of NetConductor that simplifies the creation of the overlays using an intuitive graphical user interface and automatic generation of configuration instructions that are pushed to switches and gateways. The Fabric Wizard is a tool that allows network administrators to design, deploy, and manage overlay networks using VXLAN and EVPN protocols. The Fabric Wizard provides a graphical representation of the network topology, devices, and links, and allows users to drag and drop virtual components such as VRFs, VLANs, and subnets. The Fabric Wizard also generates the configuration commands for each device based on the user input and pushes them to the switches and gateways via Aruba Central. References:
https://www.arubanetworks.com/products/network-management-operations/central/netconductor/
https://www.arubanetworks.com/assets/wp/WP_NetConductor.pdf
Policy Manager matches with Defines user and device groups and creates the associated traffic routing and access enforcement rules for the physical network Policy Manager is a solution component of NetConductor that defines user and device groups and creates the associated traffic routing and access enforcement rules for the physical network. Policy Manager is a tool that allows network administrators to create and manage network policies based on user and device identities, roles, and contexts. Policy Manager uses Group Policy Identifier (GPID) to carry policy information in traffic for in-line enforcement. Policy Manager also integrates with Cloud Auth, ClearPass, or third-party solutions to provide flexible network access control. References:
https://www.arubanetworks.com/products/network-management-operations/central/netconductor/
https://www.arubanetworks.com/assets/wp/WP_NetConductor.pdf
NEW QUESTION # 21
What is the order of operations tor Key Management service for a wireless client roaming from AP1 to AP2?
Answer:
Explanation:
Explanation
https://www.arubanetworks.com/techdocs/Instant_85_WebHelp/Content/instant-ug/wlan-ssid-conf/conf-fast-roa
NEW QUESTION # 22
You are doing tests in your lab and with the following equipment specifications
* AP1 has a radio that generates a 10 dBm signal
* AP2 has a radio that generates a 11 dBm signal
* AP1 has an antenna with a gain of 9 dBi
* AP2 has an antenna with a gain of 12 dBi.
* The antenna cable for AP1 has a 2 dB loss
* The antenna cable for AP2 has a 3 dB loss
What would be the calculated Equivalent Isotropic Radiated Power (EIRP) for APT?
- A. -12 dBm
- B. 17 dBm
- C. 26 dBm
- D. 30 dBm
Answer: D
Explanation:
Explanation
The calculated Equivalent Isotropic Radiated Power (EIRP) for AP1 is 30 dBm. EIRP is the product of the transmitter power (in dBm) and the antenna gain (in dBi) minus the cable loss (in dB). For AP1, EIRP = 10 dBm + 9 dBi - 2 dB = 17 dBm. For AP2, EIRP = 11 dBm + 12 dBi - 3 dB = 20 dBm. References:
https://www.arubanetworks.com/techdocs/ArubaOS_86_Web_Help/Content/arubaos-solutions/wlan-rf/rf-fundam
https://www.arubanetworks.com/techdocs/ArubaOS_86_Web_Help/Content/arubaos-solutions/wlan-rf/eirp.htm
NEW QUESTION # 23
What are the requirements to ensure that WMM is working effectively'? (Select two)
- A. The AP needs to be connected via a tagged VLAN to the wired port
- B. All APs need to be from the AP-5xx series and AP-6xx series which are Wi-Fi CERTIFIED 6.
- C. The APs and the controller are Wi-Fi CERTIFIED for WMM which is enabled
- D. The Client must be Wi-Fi CERTIFIED for WMM and configured for WMM marking.
- E. The Aruba AOS10 APs installed have to be converted to controlled mode
Answer: C,D
Explanation:
Explanation
These are the correct requirements to ensure that WMM (Wi-Fi Multimedia) is working effectively. WMM is a standard that provides quality of service (QoS) for wireless networks by prioritizing traffic into four categories: voice, video, best effort, and background. To use WMM, both the APs and the controller must be Wi-Fi CERTIFIED for WMM, which means they have passed interoperability tests and comply with the standard. WMM must also be enabled on the APs and the controller, which is usually the default setting. The client device must also be Wi-Fi CERTIFIED for WMM and configured for WMM marking, which means it can tag its traffic with the appropriate priority level based on the application type. The other options are incorrect because they are either not related to WMM or not required for WMM to work. References:
https://www.arubanetworks.com/techdocs/ArubaOS_86_Web_Help/Content/arubaos-solutions/wlan-qos/wmm.h
https://www.wi-fi.org/discover-wi-fi/wi-fi-certified-wmm
NEW QUESTION # 24
A large retail client is looking to generate a rich set of contextual data based on the location information of wireless clients in their stores Which standard uses Round Trip Time (RTT) and Fine Time Measurements (FTM) to calculate the distance a client is from an AP?
- A. 802.11V
- B. 802.11ah
- C. 802.11be
- D. 802.11mc
Answer: D
Explanation:
802.11mc is a standard that uses Round Trip Time (RTT) and Fine Time Measurements (FTM) to calculate the distance a client is from an AP. 802.11mc defines a protocol for exchanging FTM frames between an AP and a client, which contain timestamps that indicate when the frames were transmitted and received. By measuring the RTT of these frames, the AP or the client can estimate their distance based on the speed of light. The other options are incorrect because they either do not use RTT or FTM or do not exist as standards. Reference: https://www.arubanetworks.com/assets/wp/WP_WiFi6.pdf https://www.arubanetworks.com/assets/ds/DS_AP510Series.pdf
NEW QUESTION # 25
A customer just upgraded aggregation layer switches and noticed traffic dropping for 120 seconds after the aggregation layer came online again. What is the best way to avoid having this traffic dropped given the topology below?
- A. Configure the linkup delay timer to exclude LAGS 101 and 102, which will allow time for routing adjacencies to form and to learn upstream routes
- B. Configure the linkup delay timer to include LAGs 101 and 102, which will allow time for routing adjacencies lo form and to learn upstream routes
- C. Configure the linkup delay timer to 120 seconds, which will allow the right amount of time for the initial phase to sync
- D. Configure the linkup delay timer to 240 seconds to double the amount of lime for the initial phase to sync
Answer: B
Explanation:
The reason is that the linkup delay timer is a feature that delays bringing downstream VSX links up, following a VSX device reboot or an ISL flap. The linkup delay timer has two phases: initial synchronization phase and link-up delay phase.
The initial synchronization phase is the download phase where the rebooted node learns all the LACP+MAC+ARP+STP database entries from its VSX peer through ISLP. The initial synchronization timer, which is not configurable, is the required time to download the database information from the peer.
The link-up delay phase is the duration for installing the downloaded entries to the ASIC, establishing router adjacencies with core nodes and learning upstream routes. The link-up delay timer default value is 180 seconds. Depending on the network size, ARP/routing tables size, you might be required to set the timer to a higher value (maximum 600 seconds).
When both VSX devices reboot, the link-up delay timer is not used.
Therefore, by configuring the linkup delay timer to include LAGs 101 and 102, which are part of the same VSX device as LAG 201, you can ensure that both devices have enough time to synchronize their databases and form routing adjacencies before bringing down their downstream links.
NEW QUESTION # 26
What does the 802.3bz standard describe?
- A. AP directed roaming between APs
- B. 60 GHz P2P Wi-Fi
- C. 2.5Gb and 5Gb Ethernet ports
- D. 60 W and 90W PoE
Answer: C
Explanation:
Explanation
802.3bz is a standard for Ethernet over twisted pair at speeds of 2.5 and 5 Gbit/s. These use the same cabling as the ubiquitous Gigabit Ethernet, yet offer higher speeds. The resulting standards are named 2.5GBASE-T and 5GBASE-T.
Option A: 2.5Gb and 5Gb Ethernet ports
This is because option A shows how to identify the speed of an Ethernet port based on its name and the standard it supports. A port that supports 2.5GBASE-T or 5GBASE-T is a multi-gigabit port that can operate at speeds of up to 2.5 Gbit/s or 5 Gbit/s over twisted pair cables23.
Therefore, option A is correct.
1: https://en.wikipedia.org/wiki/2.5GBASE-T_and_5GBASE-T 2:
https://kb.netgear.com/000049004/What-is-Multi-Gigabit-Ethernet-and-how-can-I-benefit-from-using-NETGEA
https://arstechnica.com/gadgets/2016/09/5gbps-ethernet-standard-details-8023bz/
NEW QUESTION # 27
You are deploying Aruba CX 6300's with the customers requirement to only allow one (1) VoIP phone and one (1) device.
The following local role gets assigned to the phone
port-access rote VoIP device-traffic-class voice
What set of commands best fits this requirement?
- A. interface 1/1/1
aaa authentication port-access client-limit 2
aaa authentication port-access auth-mode client-mode - B. interface 1/1/1
aaa authentication port-access auth-mode multi-domain - C. interface 1/1/1
aaa authentication port-access client-limit multi-domain 2 aaa authentication port-access auth-mode multi-domain - D. interface 1/1/1
aaa authentication port-access client-limit 1 aaa authentication port-access auth-mode device-mode
Answer: C
Explanation:
Explanation
Aruba CX 6300 switches support various features to control the port access for different types of devices, such as client mode, device mode, and multidomain mode. These features can help limit the number of clients that can connect to a port and prevent unauthorized devices from accessing the network.
This is because option C shows how to configure the client limit and the auth-mode for a specific port using the interface command and the aaa authentication port-access command. The client limit specifies the maximum number of clients that can connect to a port. The auth-mode specifies the authentication mode for the port. In this case, option C sets both parameters to multi-domain mode, which allows only one voice device and one data device to be authenticated on a port
https://www.arubanetworks.com/techdocs/AOS-CX/10.10/HTML/monitoring_6300-6400/Content/Chp_LEDs/fr
https://www.arubanetworks.com/products/switches/6300-series/ 3:
https://www.arubanetworks.com/techdocs/AOS-CX/10.11/HTML/security_6200-6300-6400/Content/Chp_Port_
NEW QUESTION # 28
You are configuring Policy Based Routing (PBR) for a subnet that will be used to test a new default route for your network Traffic originating from 10.2.250.0/24 should use a new default route to 10.1.1.253. Other non-default routes for this subnet should not be affected by this change.
What are two parts of the solution for these requirements? (Select two.)
- A.
- B.
- C.
- D.
- E.
Answer: C,E
Explanation:
Explanation
Two parts of the solution for these requirements are Option C and Option E.
Option C is a part of the solution because it defines a policy-based routing action list named route_test, which specifies the next hop IP address as 10.1.1.253 for the matching traffic. This is the new default route that the user wants to use for the subnet 10.2.250.0/24. The interface null parameter indicates that the traffic will be routed to the next hop without using a specific interface1.
Option E is a part of the solution because it applies the policy-based routing action list route_test to the VLAN interface 250, which has an IP address of 10.2.250.1/24. This is the subnet that the user wants to test the new default route for. The apply policy command enables policy-based routing on the interface and associates it with the action list2.
Option A is not a part of the solution because it defines a policy-based routing action list named route_test, but does not specify the next hop IP address as 10.1.1.253, which is the new default route that the user wants to use. Instead, it specifies a next hop IP address of 10.1.1.254, which is different from the requirement.
Option B is not a part of the solution because it defines a policy-based routing action list named route_test, but does not specify any next hop IP address at all, which is necessary for policy-based routing to work. Instead, it specifies an interface null parameter without any IP address, which is invalid.
Option D is not a part of the solution because it applies the policy-based routing action list route_test to the VLAN interface 200, which has an IP address of 10.2.200.1/24. This is not the subnet that the user wants to test the new default route for, but a different subnet that should not be affected by this change.
NEW QUESTION # 29
Refer to the image.
Your customer is complaining of weak Wi-Fi coverage in their office. They mention that the office on the other side of the hall has much better signal What is the likely cause of this issue7
- A. The AP is a remote access point.
- B. The AP is configured in Mesh mode
- C. The AP is using a directional antenna.
- D. The AP is an outdoor access point.
Answer: C
Explanation:
The likely cause of the issue of weak Wi-Fi coverage in the office is that the AP is using a directional antenna. A directional antenna is an antenna that radiates or receives radio waves more strongly in one or more directions, creating a focused beam of signal. A directional antenna can provide better coverage and performance for a specific area, but it can also create dead zones or weak spots for other areas. The other options are incorrect because they either do not affect the Wi-Fi coverage or do not match the scenario. Reference: https://www.arubanetworks.com/techdocs/ArubaOS_86_Web_Help/Content/arubaos-solutions/wlan-rf/rf-fundamentals.htm https://www.arubanetworks.com/techdocs/ArubaOS_86_Web_Help/Content/arubaos-solutions/wlan-rf/antennas.htm
NEW QUESTION # 30
You are helping an onsite network technician bring up an Aruba 9004 gateway with ZTP for a branch office The technician was to plug in any port for the ZTP process to start Thirty minutes after the gateway was plugged in new users started to complain they were no longer able to get to the internet. One user who reported the issue stated their IP address is 172.16 0.81 However, the branch office network is supposed to be on 10.231 81.0/24.
What should the technician do to alleviate the issue and get the ZTP process started correctly?
- A. Turn off the DHCP scope on the gateway, and set DNS correctly on the gateway to reach Aruba Activate
- B. Move the cable on the gateway from port G0/0V1 tc port G0 0.0
- C. Factory default and reboot the gateway to restart the process.
- D. Move the cable on the gateway to G0/0/1. and add the device's MAC and Serial number in Central
Answer: B
Explanation:
Explanation
Aruba 9004 gateway supports ZTP on port G0/0/0 by default1. If the gateway is connected to a different port, such as G0/0/V1, it will not be able to communicate with Aruba Activate and Aruba Central, which are required for ZTP2. Moreover, port G0/0/V1 is configured as a DHCP server by default, which can cause IP address conflicts with the existing network3. Therefore, the technician should move the cable on the gateway to port G0/0/0, which will allow the gateway to obtain an IP address from the network DHCP server and start the ZTP process. The other options are not correct because they will not solve the issue or enable ZTP. For example, option D will not work because factory defaulting and rebooting the gateway will not change the port configuration or behavior3.
NEW QUESTION # 31
Your Director of Security asks you to assign AOS-CX switch management roles to new employees based on their specific job requirements. After the configuration was complete, it was noted that a user assigned with the auditors role did not have the appropriate level of access on the switch.
The user was not allowed to perform firmware upgrades and a privilege level of 15 was not assigned to their role. Which default management role should have been assigned for the user?
- A. sysops
- B. administrators
- C. sysadmin
- D. config
Answer: A
Explanation:
The correct answer is B. sysops.
The sysops user role is a predefined role that allows users to perform system operations on the switch, such as backup, restore, upgrade, or reboot. The sysops user role also has access to the PUT and POST methods for REST API, which can be used to modify the switch configuration. The sysops user role has a privilege level of 15, which is the highest level of access on the switch1.
The other options are incorrect because:
A) sysadmin: The sysadmin user role is a predefined role that allows users to view and modify the switch configuration using the CLI or the Web UI. The sysadmin user role does not have access to the REST API methods, and cannot perform firmware upgrades1.
C) administrators: The administrators user role is a predefined role that has full access to all switch configuration information and all REST API methods. This role is more than what the Director of Security requires1.
D) config: The config user role is a predefined role that allows users to view and modify the switch configuration using the CLI or the Web UI. The config user role does not have access to the REST API methods, and cannot perform firmware upgrades1.
NEW QUESTION # 32
Review the exhibit.
You are troubleshooting an issue with a 10 102.39 0/24 subnet which is also VLAN 1000 used Tor wireless clients on a pair of Aruba CX 8360 switches The subnet SVI is configured on the 8360 pair, and the DHCP server is a Microsoft Windows Server 2022 Standard with an IP address of 10 200 1.100. The 10.102.250.0/24 subnet is used for switch management.
A large number of DHCP requests are failing You are observing sporadic DHCP behavior across clients attached to the CX 6100 switch.
Which action may help fix the issue?
- A.
- B.
- C.
- D.
Answer: D
Explanation:
Explanation
Option C is the only action that configures the DHCP relay on the SVI of VLAN 1000 on the CX 8360 switches. DHCP relay is a feature that allows a switch to forward DHCP requests from clients in one subnet to a DHCP server in another subnet. DHCP relay is required when the DHCP server and the clients are not in the same broadcast domain1.
Option C uses the following commands:
* interface vlan 1000: This command enters the interface configuration mode for the SVI of VLAN 1000, which has an IP address of 10.102.39.1/24 and is used for wireless clients.
* ip helper-address vrf default 10.200.1.100: This command configures the IP address of the DHCP server as a helper address for the SVI, which means that the switch will forward DHCP requests from clients on VLAN 1000 to this address. The vrf default parameter indicates that the SVI and the DHCP server are in the same VRF.
NEW QUESTION # 33
When setting up an Aruba CX VSX pair, which information does the Inter-Switch Link Protocol configuration use in the configuration created?
- A. hello interval is 1s by default
- B. hello interval is disabled by default
- C. hello interval 100ms by default
- D. hello interval is based on the value set by dead interval
Answer: A
Explanation:
The reason is that the Inter-Switch Link Protocol (ISLP) is a protocol that enables VSX stack join and synchronization between two VSX peer switches. ISLP uses a hello interval to exchange control messages between the switches.
The hello interval is a parameter that specifies the time interval between sending hello messages. The default value of the hello interval is 1 second. The hello interval can be configured from 1 second to 10 seconds.
https://www.arubanetworks.com/techdocs/AOS-CX/10.04/HTML/5200-6728/index.html
NEW QUESTION # 34
A new network design is being considered to minimize client latency in a high-density environment. The design needs to do this by eliminating contention overhead by dedicating subcamers to clients.
Which technology is the best match for this use case?
- A. MU-MIMO
- B. OFDMA
- C. Channel Bonding
- D. QWMM
Answer: B
Explanation:
Explanation
OFDMA (Orthogonal Frequency Division Multiple Access) is a technology that can minimize client latency in a high-density environment by eliminating contention overhead by dedicating subcarriers to clients. OFDMA allows multiple clients to transmit simultaneously on different subcarriers within the same channel, reducing contention and increasing efficiency. MU-MIMO (Multi-User Multiple Input Multiple Output) is a technology that allows multiple clients to transmit simultaneously on different spatial streams within the same channel, but it does not eliminate contention overhead. QWMM (Quality of Service Wireless Multimedia) is a technology that prioritizes traffic based on four access categories, but it does not eliminate contention overhead. Channel Bonding is a technology that combines two adjacent channels into one wider channel, increasing bandwidth but not eliminating contention overhead. References:
https://www.arubanetworks.com/assets/ds/DS_AP510Series.pdf
https://www.arubanetworks.com/assets/wp/WP_WiFi6.pdf
NEW QUESTION # 35
......
To take the HP HPE7-A01 exam, candidates must have a basic understanding of networking concepts and protocols, as well as experience working with Aruba products such as ArubaOS, ClearPass, and AirWave. HPE7-A01 exam consists of 60 multiple-choice questions and has a time limit of 90 minutes. A passing score of at least 70% is required to obtain the certification.
HP HPE7-A01 exam is designed to test the knowledge and skills of IT professionals about the Aruba campus access solutions. Aruba Certified Campus Access Professional Exam certification focuses on providing individuals with a thorough understanding of network access and the design, implementation, and operation of secure wireless and wired networks. HPE7-A01 exam is sought after by network professionals who want to validate their expertise in managing and configuring wireless systems while ensuring secure device and user access.
Use Valid New HPE7-A01 Test Notes & HPE7-A01 Valid Exam Guide: https://www.real4prep.com/HPE7-A01-exam.html
HPE7-A01 Actual Questions Answers PDF 100% Cover Real Exam Questions: https://drive.google.com/open?id=1cz5UqF08-03jhi4bedds-Gc4Jo_bkMdr