2023 Latest 100% Exam Passing Ratio - 4A0-113 Dumps PDF
Pass Exam With Full Sureness - 4A0-113 Dumps with 105 Questions
NEW QUESTION # 30
What address is used when RIPv2 uses multicast to send its updates?
- A. RIPv2 does not have support for multicast
- B. 224.0.0.9
- C. 224.0.0.10
- D. 224.0.0.6
- E. 224.0.0.5
Answer: B
NEW QUESTION # 31
What are the ways the RID can be created on an Nokia 7750 SR router? (Choose three)
- A. The loopback IP address
- B. From the system IP address
- C. From the highest interface IP address
- D. From the last 32 bits of the chassis MAC address
- E. By using the command "config router ospf rid X.X.X.X"
- F. From the first 32 bits of the chassis MAC address
Answer: B,D,E
NEW QUESTION # 32
Click the exhibit button.
A static route is created on router R1 "using the "static-route 0.0.0.0/0 next-hop 10.3.3.2" command. What command can be used to test the static route on an Nokia 7750 SR?
- A. ping 0.0.0.0
- B. ping static 10.5.5.5
- C. ping static 0.0.0.0/0
- D. ping 10.5.5.5
Answer: D
NEW QUESTION # 33
Exhibit
Given the two configurations shown, identify the two incorrect statements below: (Choose two)
- A. The system interface is missing in one configuration so OSPF will not operate correctly.
- B. The interface type settings differ, but OSPF will still operate correctly.
- C. Both routers will generate OSPF Hello packets.
- D. Metric values differ, but this does not prevent OSPF operation.
Answer: A,B
NEW QUESTION # 34
Which of the following statements best describes the function of an OSPF Type 4 LSA?
- A. A Type 4 LSA is originated by an ABR that is connected to a stub area. The LSA is injected into the stub area to provide routing information.
- B. A Type 4 LSA is originated by an ABR that is connected to a stub area. The LSA is injected into the backbone area to provide routing information.
- C. A Type 4 LSA is originated by an ASBR to describe a route to itself to routers outside the area.
- D. A Type 4 LSA is originated by an ABR to describe a route to an ASBR to routers outside the area.
Answer: D
NEW QUESTION # 35
What is the protocol number for OSPF in the IP header?
- A. OSPF uses TCP, so the protocol number is 6.
- B. OSPF has its own protocol number of 89.
- C. OSPF uses UDP, so the protocol number is 17.
- D. OSPF does not use IP.
Answer: B
NEW QUESTION # 36
Click the exhibit button.
The OSPF packets shown have been exchanged between two neighbors. What state is the OSPF adjacency in?
- A. The adjacency state is full. The routers are exchanging database description packets to notify each other that all link state advertisements have been received.
- B. The adjacency is in the exchange state. The next step is to exchange link state request and link state update packets.
- C. The adjacency state is two way because both routers have received a database description packet.
- D. The adjacency is in the ex start state. The routers have exchanged database description packets, but still have to negotiate the starting sequence number.
Answer: D
NEW QUESTION # 37
Click the exhibit button.
192.168.3.1 is a loopback interface on router R2 and is distributed to OSPF area 0, but the ping fails from router R3. Which of the following is a possible solution to the problem?
- A. Add the "originate-default-route" option in the NSSA area configuration on router R3
- B. Make a default route on router R2
- C. Make a static route on router R1 to 192.168.3.1
- D. Add the "summaries" option to the NSSA area configuration on router R1
Answer: D
NEW QUESTION # 38
What causes an adjacency to change from down to two ways?
- A. When a router receives a database description packet from a neighbor.
- B. When a router receives a Hello packet that contains its own router ID in the neighbor list from a neighbor.
- C. When a link state acknowledgement is received in response to a link state update.
- D. When a link state update is received in response to a link state request.
Answer: B
NEW QUESTION # 39
Refer to the exhibit.
Assume that OSPFv3 is properly configured on all routers and that R4 advertises its system prefix into Area 0. Which of the following statements best describes how R5 learns R4's IPv6 system prefix?
- A. With a Router LSA originated by R4
- B. With a Router LSA originated by R1
- C. With an Inter-Area Prefix LSA originated by R1
- D. With a Router LSA originated by R5
- E. With an Inter-Area Prefix LSA originated by R5
- F. With an Inter-Area Prefix LSA originated by R4
Answer: C
NEW QUESTION # 40
In an OSPF Hello packet, which of the following fields must match for all neighbor routers on the segment? Choose three answers.
- A. Checksum values
- B. Area ID W B.
- C. Hello and Dead intervals PC.
- D. The list of neighbors
- E. Stub flag
Answer: B,C,E
NEW QUESTION # 41
Which of the following concerning OSPFv3 is TRUE?
- A. OSPFv3 uses a 64-bit router ID.
- B. OSPFv3 uses MD5 Authentication.
- C. Router LSAs carry IPv6 prefix information.
- D. NSSA is supported in OSPFv3.
Answer: D
NEW QUESTION # 42
Click the exhibit button.
Routers R1 , R2, and R3 are running a classful routing protocol between them. Assuming that router R1 advertises all directly connected networks, how will these networks be represented in router R3's routing table?
- A. The networks will be represented with one entry of 10.0.0.0/24 in router R3's route table.
- B. The networks will be represented with one entry of 10.0.0.0/8 in router R3's routing table.
- C. Router R3's routing table will have one entry for 10.1.1.0/24 and one entry for 10.1.2.0/24.
- D. Router R3's routing table can only contain one of the routes, which will result in route flapping.
Answer: B
NEW QUESTION # 43
A static route is created using the command "static-route 0.0.0.0/0 next-hop 3.3.3.1". What command could be used to test the static route on an Nokia 7750 SR?
- A. Ping 3.3.3.1
- B. Ping static 0.0.0.0/0
- C. Ping static 3.3.3.1
- D. Ping 0.0.0.0
Answer: A
NEW QUESTION # 44
In an IP datagram, which of the following fields identifies the receiving application?
- A. The protocol field of the network layer header.
- B. The protocol field of the transport layer header.
- C. The port field of the transport layer header.
- D. The port field of the network layer address.
Answer: C
NEW QUESTION # 45
An OSPF adjacency is stuck in the exstart state. What is the most likely cause?
- A. An OSPF Hello has not been received from the neighbor.
- B. The MTU does not match on both interfaces.
- C. The interfaces are configured as point-to-point on one side and broadcast on the other.
- D. OSPF is not enabled on one of the routers.
- E. The router ID is the same on both routers.
Answer: B
NEW QUESTION # 46
......
Verified 4A0-113 dumps Q&As - 100% Pass from Real4Prep: https://www.real4prep.com/4A0-113-exam.html
Pass 4A0-113 Exam in First Attempt Guaranteed 2023 Dumps: https://drive.google.com/open?id=1oezRopdZCMpF0YOqjX6Y6Ow9K2NwXOQ8